Specs Network communication unit DL series

Model

DL-EP1^*1

Image

Indicator

Link/activity indicator (LINK/ACT): Green LED, Module status indicator (MS): 2-colour (green/red) LED,
Network status indicator (NS): 2-colour (green/red) LED, Sensor communication indicator (D-bus) 2-colour (green/red) LED

Ethernet
specifications

Compliant standards

IEEE802.3 (10BASE-T)/IEEE802.3u (100BASE-TX)

Transmission speed

10Mbps (10BASE-T)/100Mbps (100BASE-TX)

Transmission interface

STP cable or Category 3 or higher UTP cable (10BASE-T)/STP cable or Category 5 or higher UTP cable (100BASE-TX)

Maximum cable length

100 m (Distance between DL-EP1 and Ethernet switch)

Sensor
connection
specifications

Connectable
sensors

Sensor amplifiers with D-bus support ^*2

Number of
connectable
sensor units

Up to 15 units

Ethernetspecifications

Maximum number of connectable hubs

4 (10BASE-T)/2 (100BASE-TX)

EtherNet/IP™specifications

Supported functions

Cyclic communication (Implicit messaging)
Message communication (Explicit messaging)
Compatible with UCMM and Class 3

Number of connections

64

RPI (communication cycle)

0.5 to 10000 ms (0.5 ms unit)

EtherNet/IP™ specifications

Tolerable communication bandwidth for cyclic communication

6000pps

EtherNet/IP™specifications

Conformance test

Compatible with Version A7

Power voltage

20 to 30 VDC, including ripple (p-p) 10% (This voltage is supplied from the connected sensor amplifier)

Power consumption

1500 mW or less (at 30 V 50 mA max)

Environmental resistance

Pollution degree

2

Ambient temperature

-20 to +55 °C (No freezing)

Relative humidity

35 to 85 % RH (No condensation)

Vibration resistance

10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions

Material

Main unit case: Polycarbonate

Weight

Approx. 70 g

Model

DL-PD1

Image

Sensor
connection
specifications

Connectable
sensors

Sensor amplifiers with D-bus support^*1

Number of
connectable
sensor units

15 units max.^*2

PROFIBUS
DP
specifications

Device type

DP-V1 Slave (D-sub 9 pin, Number of the ports: 1)

Communication speed

9.6 kbit/s to 12 Mbit/s

Cable length

9.6 / 19.2 / 45.45 / 93.75 kbit/s : 1200 m
187.5 kbit/s : 1000 m
500 kbit/s : 400 m
1.5 Mbit/s : 200 m
3 / 6 / 12 Mbit/s : 100 m

Power voltage

20 to 30 VDC, including ripple (p-p) 10%
(This voltage is supplied from the connected sensor amplifier.)

Power consumption

1600 mW or less (65 mA max. at 24 V)

Environmental resistance

Ambient temperature

-20 to +55 °C (No freezing)

Relative humidity

35 to 85 % RH (No condensation)

Vibration resistance

10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions

Shock resistance

500 m/s², 3 times in each of the X, Y, and Z directions

Material

Main unit case and dust cover: Polycarbonate PROFIBUS connector: Steel – Nickel plating

Weight

Approx. 65 g

Model

DL-CL1^*1

Image

Supported version

Version 2.00, version 1.10 (switchable)

CC-Link specifications

No. of occupied stations

Ver. 2.00: 1 station, 8 times/2 stations, 8 times/4 stations, 2 times
(switchable), Ver. 1.10: 1/2/4 stations (switchable)

Station type

Remote device station

Transmission speed

156 kbps/625 kbps/2.5 Mbps/5 Mbps/10 Mbps

Station number settings

1 to 64

Power voltage

20 to 30 VDC, including ripple (P-P) 10 % (supplied from the connected sensor amplifiers)

Weight

Approx. 80 g

Model

DL-RS1A^*1

Image

Synchronisation between the transmitter and receiver

Asynchronous

Transmission code

ASCII

Baud rate

2,400/4,800/9,600/19,200/38,400 bps selectable (Factory-setting: 9,600 bps)

Data bit length

8 bits/7 bits selectable (Factory-setting: 8 bits)

Parity check

None/Even/Odd selectable (Factory-setting: None)

Stop bit length

1 bit

Data delimiter

Data reception: automatically recognizes CR or CR+LF
Data transmission: Fixed to CR+LF

Indicator

Communication indicator lamp (green x 2), Alarm indicator lamp (red),
Power indicator lamp (green)

Sensor
connection
specifications

Number of
connectable
sensor units

Up to 15 units (including main unit)

Power voltage

20 to 30 VDC, including ripple, Ripple (P-P): 10 % max. Class 2 (Supplied via connected sensor amplifier)

Power consumption

25 mA max.

Environmental resistance

Ambient temperature

-10 to +55 °C

Relative humidity

35 to 85 % RH (No condensation)

Vibration resistance

10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions

Material

Case/Polycarbonate

Weight

Approx. 53 g

Communication method

Full duplex

Model

DL-DN1^*1

Image

DeviceNet® specifi cations

Network power supply

11 to 25 VDC (supplied from DeviceNet® communication power supply)

Indicator

Network status indicator: 2-colour (green/red) LED, Module status indicator: 2-colour (green/red) LED,
Sensor communication indicator: 2-colour (green/red) LED

Sensor
connection
specifications

Connectable
sensors

Sensor amplifiers with D-bus support^*2

Number of
connectable
sensor units

Up to 15 units

DeviceNet® specifi cations

Compliant functions

Remote I/O communication (polling) Explicit messaging

Address setting

0 to 63 (PGM compatible)

Baud rate (automatically switched)

500 kbps/250 kbps/125 kbps

Maximum cable length

500 kbps

thick cable

100 m

thin cable

250 kbps

thick cable

250 m

thin cable

100 m

125 kbps

thick cable

500 m

thin cable

100 m

Power voltage

20 to 30 VDC, including ripple (P-P) 10 % (supplied from the connected sensor amplifiers)

Power consumption

660 mW or less (at 30 V, 22 mA max.)

Environmental resistance

Pollution degree

2

Ambient temperature

-20 to +55 °C (No freezing)

Relative humidity

35 to 85 % RH (No condensation)

Vibration resistance

10 to 55 Hz, Double amplitude 1.5 mm, 2 hours in each of the X, Y, and Z directions

Material

Main unit case and dust cover: Polycarbonate, DeviceNet® connector: Polyamide (plug), PUT (socket)

Weight

Approx. 80 g